Why Understanding Plumbing Basics is Essential For Installing a Bathtub
Why Understanding Plumbing Basics is Essential For Installing a Bathtub
Blog Article
This article listed below pertaining to A Step-by-Step Guide to Installing a Bathtub is exceedingly informative. Try it and make your own assumptions.
Mounting a bathtub isn't precisely brain surgery, but it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is conveniently available, the project can relocate speedily; if you need to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to vacate the old tub and set in the new one. See to it you have actually certified yourself for the job and are comfortable trying it. Instead of employing a contractor to take over a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your restroom if you have actually currently acquired a new bathtub and also do not require to change the arrangement of your previous water system pipes.
Your tools and product checklist must consist of the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly bothersome because of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in place between the tap and the sink. Protect the faucet in position with the manufacturer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be attached to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the required placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little points.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub up until the spirit level reviews level.
To install taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water and check all joints as well as brand-new pipework for leakages and tighten them if necessary. Load the bath tub as well as additionally check the overflow outlet and also the normal outlet for leakages.
Finally, fix the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has been used a minimum of once as this will settle it right into its last position.
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now be ready to be suited its final position.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall in between the bath and also the tiling, bring about difficulties with wetness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture rather very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about Installing A Bathtub. Thanks a ton for spending some time to read through our blog. For those who liked our post kindly remember to pass it around. We appreciate reading our article about How to Install a Bathtub.
Detail Report this page